This write-up about how to make three Quick Do it yourself Floating Photograph Frames And How to Reduce Plexiglass is sponsored by The Property Depot as component of the #THDProSpective Software. It also includes affiliate back links. See policies.
Effortless Diy image frames are basically a single of my most asked for tutorials and oddly sufficient, until eventually now, I didn&rsquot have numerous to share!
.
I basically designed my dad a big Do it yourself custom made image frame as a Christmas gift a couple years back and shared the tutorial for it here. But it used dowels, and a router, and it may have been a small additional concerned than most persons are wanting for.
So, in this put up, I&rsquom likely to clearly show you how I built 3 various fashion Tremendous Uncomplicated Do it yourself floating photograph frames with just two simple instruments. I&rsquoll also display you how quick it is to cut plexiglass for them, too!
.
So if you&rsquore completely ready to get setting up, let&rsquos go! I&rsquove got the movie tutorial here and the move by stage beneath:
Equipment AND Resources:
- Miter noticed (or any wood slicing noticed is great&ndashdoesn&rsquot have to be a MITER observed)
- Nail Gun (optional, just tends to make items more rapidly)
- Wooden Glue
- ¾&Key sq. dowels
- one×2 boards
- ¼&Prime x one ⅛&Key lattice trim
- Thin Plexiglass Sheets
- Ryobi A single+ HP Slash Off Instrument (employed to cut plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in put of clamps to keep items whilst wooden glue dries)
- Switch buttons
A Take note About FLOATING Picture Frames:
I&rsquom sharing how to make three diverse design and style FLOATING photograph frames in this tutorial, but the to start with step to producing any of them is cutting the plexiglass to the dimensions you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this move. But because the graphics/pictures I framed are &ldquofloating&rdquo inside of the frame, they&rsquore basically sandwiched involving two parts of plexiglass. So plexiglass/acrylic is needed to be capable to &ldquofloat&rdquo your photo.
.
To make points effortless to adjust out in these frames, I also used these change buttons&mdashor I simply call them twisty tabs&ndashon the again to maintain the plexiglass in put.  
HOW TO Slice PLEXIGLASS
Normally, I have my community glass shop reduce my glass and plexiglass parts for my jobs.  But considering the fact that these plexiglass items will be modest and various customized sizes, it would be a lot cheaper, more rapidly and simpler to just reduce them myself.
.
I made use of some (about) ⅛&rdquo acrylic sheets from Household Depot.  They appear in a variety of measurements, all the way up to a four×8 sheet.  I just grabbed some 11x14s.
I designed some easy graphics on my computer system (PicMonkey and Canva are terrific for this!) and also made use of a patch that I received a handful of yrs back at a convention for these frames.  You can use a photograph, a poster, cloth, no matter what you want to body for this.
.
I laid them out on my sheet how I liked the spacing, then marked exactly where I wished to reduce&ndashno measurements below&hellipjust eyeballing how I assumed the spacing about the graphic appeared very good.
Now, I&rsquove made use of the inexpensive tiny hand knife they assert will minimize plexiglass before and it was a awful expertise with very weak outcomes.  I&rsquove also used a jig saw to lower plexiglass and it melts, gets trapped, then chips or cracks the sheet.
.
So THIS time, I attempted this new Ryobi 1+ HP Compact Lower Off Tool with a plastic chopping blade and was carefully impressed with how swift and clean the cuts were being.
When I 1st observed this instrument, I identified it sort of weird hunting.  But following I applied it, I comprehended the idea. 
.
It&rsquos mainly a hybrid in between a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety degrees. 
.
It&rsquos compact and light-weight and it&rsquos obtained a forward and reverse change to transform the blade equally directions.  It&rsquos also received a variable velocity cause&mdashwhich is good for cutting plastic to support avoid melting. 
It will come with a plastic and drywall blade, a metallic slash off wheel, and a diamond blade for cutting tile and cement board.  You can study much more about the new Ryboi Just one+ HP minimize off device at the link listed here if you&rsquore fascinated.
.
For reducing straight traces on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the steel blade guard towards it to make the minimize.  You can skip the straight edge and freehand these cuts, also if you have a continual hand. (I don&rsquot haha!)
I did come across it reduce very best in this situation with the swap in reverse. It seemed to not soften that way.
.
I cut two parts equivalent in measurement for just about every product I was framing. Then, I was prepared to commence generating the genuine floating photograph frames.
Simple Do it yourself FLOATING Photograph Body Design and style one
Design one is my private preferred, so I&rsquoll commence with it 😊
This specific floating photograph frame style needs ¾&Primary square dowels and one×2 board. It is mainly just a 1×2 wrapped about a sq. dowel frame.
.
I made use of ¾&rdquo square dowels for this and established up my miter noticed to cut 45 levels.  Now, you don&rsquot have to miter these.  You can depart it on ninety and make butt joints.  You also don&rsquot will need a MITER noticed for this.  Any saw that you can slash rather straight with will do the job great.
.
I generally trimmed four parts of square dowel so that when match jointly, they&rsquod be just scarcely (like ⅛&Key) larger than the plexiglass piece I was putting in it.
I utilized wood glue to the corners and nailed them with each other with brad nails.  If you are affected person, and don&rsquot have a nail gun, just glue and clamp until finally dry.
.
Right after the glue had dried, I cut to suit 1×2 parts with forty five diploma mitered corners all around this frame.& page , butt joints are great right here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s all-around the edges leaving about ¼&rdquo sticking out the back facet of the plexiglass, so that when I set up the two ⅛&Primary plexiglass pieces, it&rsquoll be flush across the again side of the body.
Then, I screwed these twisty tabs into the back sides of the frame to hold the plexiglass in place.  I&rsquoll go again and thoroughly clean the sawdust off the plexiglass later on, but for now, I established this off to the facet to make the upcoming body.
Simple Do-it-yourself FLOATING Image FRAMES Design and style two
Design and style 2 is a little less difficult and is produced of 1x2s and ¼&rdquo thick by one ⅛&Key broad lattice trim.
I commenced by slicing down the lattice items so it would make a body that the plexiglass would in shape Inside of.  Once again, just like in advance of, the mitered corners are optional.
At the time I experienced this lattice frame lower, I measured its over-all measurement and cut 1×2 parts to make a body whose over-all measurement matched that of the lattice body. See underneath 1×2 frame laying on prime of lattice body&ndashthey&rsquore the exact dimensions.
I glued and nailed the one×2 frame jointly and clamped until dry. Yet again, you can use super glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice frame onto the back again.  I made use of a major item to keep it in location until eventually it was dry, then, I screwed twisty tabs on the back to maintain the plexiglass in spot. 
Because the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass parts are put inside, almost everything ought to sit flush throughout the back just like the previous frame.
Once more, I&rsquoll go again and cleanse the sawdust off afterwards, but for now, I moved on to the previous model frame.
Easy Diy FLOATING Picture Frame Style three
Design and style three is the exact strategy as fashion 1, but alternatively of working with 1x2s, I utilised ¼&Primary x 1 ⅛&Primary lattice trim to maintain the frame a tiny thinner and more minimalist searching.
So, I reduce ¾&rdquo square dowels to make a body the same measurement or slightly more substantial than the plexiglass I was framing and glued and nailed it collectively.
Then, I minimize lattice trim to wrap all-around that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back facet of the square dowel body so that when the two items of ⅛&rdquo plexiglass are mounted, it&rsquoll all be flush across the back again.
.
I didn&rsquot have any brad nails shorter ample to nail this frame on, so I only glued and clamped until finally it was dry.
If you don&rsquot have clamps, you can use painters tape to kind of wrap all around the items to keep right until the glue dries OR merely use some super glue or CA glue to assist hold parts in location until eventually the true wooden glue is fixed.
.
Then, just like the previous two frames, I installed twisty tabs to keep the plexiglass in position.
FLOATING Photo Body HANGING Solutions
The ultimate move is clean up up and hanging.  I utilised some glass cleaner to thoroughly clean up all the noticed dust, then made use of a piece of double sided tape on the back again plexiglass piece to make guaranteed the shots continue to be in spot, then set the frames back alongside one another.
.
To hang, you can use your standard sawtooth hangers for this.
Or basically position it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and cling it on a piece of wooden dowel you screwed into the wall.
As you can see, generating photo frames doesn&rsquot have to be complex.  This is a great newbie challenge you can deal with with small resources and get as inventive as you want. 
.
I actually hung these graphics up in my desk region to enable retain me inspired when working by yourself from residence suitable now. So, now that my desk area is comprehensive, I guess I must almost certainly get back again to do the job 😊
I hope you&rsquove enjoyed this small undertaking.  There are lots a lot more coming your way, so be sure to subscribe to my publication below so you don&rsquot overlook out on what&rsquos coming future!
.
And don&rsquot neglect to pin this for later!
Right up until following time, pleased creating 😊
 
